Environments

Morbern — Application request cards

Pick the environment first. The vinyl comparison changes when spray, contract cleaning, or pattern cutting is the real constraint.

Application request cards

Comfort and daily contact
Discuss
Touch, care, and appearance on the surface a person actually meets. Marine cushions and contract seats both need a hand description, but the cleaner, the sit time, and the light on the face are not the same. Write whether the grain should stay matte after wiping, and whether the colour is being judged in daylight or under a cabin lamp. A vinyl that feels dry on a cutting table can feel different once it is wrapped over foam. Say which of those states is the approval state.
Include
The material reference and the part name: cushion top, inside arm, helm seat, banquette, or task chair. Add the backing you expect if the cover is glued rather than sewn. If the inquiry mentions morbern vinyl or a specific Allsport colour, keep that string as the locator and still describe the face you have in the sample. Daily contact does not require a waterproofness number. It does require an honest note of abrasion risk and the cleaning chemistry in use. Those notes tell a later reader which method would be relevant. They are not themselves a test report.
Outdoor and performance
Discuss
Spray, standing water, sun, and cabin heat are separate from indoor contract wear. Water resistance and vapour movement are different properties, and a coated vinyl face is not a breathable membrane by default. Say whether you need liquid shed, colour hold under light, or flexibility when the vinyl is cold.
Include
Construction and specimen state. Name whether the sample is a face chip, a backed swatch, or a sewn cover. For a Prodigy or other marine reference, state the boat area and whether the vinyl is flat or stretched over a curve. Usable width matters only if the panel layout depends on it. Do not borrow a hydrostatic or weathering figure from a different coated cloth. Ask for the method, the date, and the batch if a number is going to be used at all.
Processing and technical use
Discuss
Cutting yield follows usable width and grain direction. Sewing depends on the backing and on whether the coating cracks at the stitch. Bonding depends on the adhesive and the substrate. Four-way stretch needs a note on elongation, because recovery is separate from the grain you see. This card records process conditions. It does not say every construction can be wrapped or sewn the same way.
Include
Dimensions and process conditions you already know: cuttable width target, panel size, stitch type, adhesive family, and the temperature of the shop if it is extreme. Quantity and destination can sit in the same message so the format question is clear, whether that format is a roll or a cut length. Leave lead time and minimums out unless a document in front of you states them. If a finish record is required before bonding, ask for that record by the material name rather than by a general coating claim.
Selection trade-offs
Coating or lamination
A coated face is judged by coating add-on, adhesion to the backing, and how soft the hand stays after that add-on. A laminated construction is judged by the film, peel at the bond line, and the specimen state: face chip, backed swatch, or sewn cover. Morbern pages do not assign either build to a trade name. Ask which build the reference actually is before comparing seam slippage or tear strength.
Abrasion or hand
An abrasion-resistance reading needs the method, the end point, and the batch. It does not describe pilling, grain loss, or how the vinyl feels after contract cleaning. Hand and colourfastness need the same sample in the light and with the cleaner the seat will meet. One number cannot stand in for the other.
Stock or development
A stock conversation needs a dated lot, shade band, and batch traceability. This profile does not publish inventory, so an inquiry cannot assume a colour is on hand. A development conversation needs a lab dip or a dated swatch, a written trial, and a separate bulk approval. Those steps are not a lead time and not a minimum.
What a number still cannot do
Hydrostatic head and water vapor transmission answer different questions, and a vinyl face is not assumed to pass either. Tensile strength needs the specimen direction and the method version. If mass is compared, name the conditioning, commonly 20 °C and 65% relative humidity for textile atmospheres, and state that this is a method request, not a Morbern result. Usable width, GSM, and fiber composition stay open until a specimen record fills them.

Describe the use environment

Exposure, care, and processing make the brief specific enough to compare vinyl without inventing a result.

Discuss your fabric requirements